Drake Landing Solar Community
Home / Solar panels / Flat roof solar panels: what to know before installing

Flat roof solar panels: what to know before installing

Solar panels work well on a flat roof. A flat roof gives the installer freedom to choose how the panels sit, but the mounting system has to secure the array against uplift without damaging the roof membrane, and the structure underneath needs to carry the extra mass, including snow in a Canadian winter.

Last updated

Can you install solar panels on a flat roof?

Yes, in most cases. Installing solar panels on a flat roof is routine, since flat roofs are common on garages, commercial buildings, additions, townhouses and many older bungalows, and home solar energy systems are placed on them every year. The main difference from a pitched roof is that a flat roof has no slope of its own. Panels lie almost flat unless the frames lift them, so the installer decides the tilt and the spacing between rows.

That freedom is useful. On a sloped roof the panels follow the roof, even if it faces the wrong way. On a flat roof, the array can face south at a good angle, which is why many flat roof installations out-produce panels laid on a poorly oriented slope. The trade-off is extra hardware and more attention to drainage and wind.

Drake Landing Solar Community used a similar idea with its 800 flat-plate collectors, which sat on garage roofs in tilted rows; the solar collection page shows how that array was laid out. Those were heat collectors, not photovoltaic panels, but the same geometry of row spacing and shade applies.

How are solar panels mounted on a flat roof?

There are two broad approaches, and many systems combine them.

Ballasted mounting. A ballasted system holds the frames down with weight, usually concrete blocks or pavers, rather than with screws through the roof. Because nothing is fixed to the roof deck, the design is called non-penetrative, and the waterproofing stays intact. That suits a newer flat roof solar installation or one still under warranty. The catch is that the blocks add a noticeable load per square metre, and the roof structure has to be able to carry it.

Attached (penetrating) mounting. Here the frames are bolted to the structure through the roof, with flashing and sealant around each fixing. These racking systems are lighter because the building itself resists the wind. They work where the roof cannot take much extra mass. The cost is a set of penetrations, each of which must be sealed properly by someone who understands the roofing system. See solar panel roof leaks and flashing for how those details fail and what to ask about them.

A hybrid design uses blocks across most of the array and a few mechanical fixings, often at the edges and corners. The balance depends on the building height, the exposure and what the structure can carry, and it helps to ensure that the mounting suits the roof area.

What tilt angle and direction work best?

Flat roof mounting systems typically hold panels at a shallow tilt, often somewhere around 10 to 15 degrees, though steeper settings are used where shedding snow matters more. A low tilt means smaller forces, lighter ballast and shorter shadows between rows, at the cost of a little yield compared with a steeper south-facing array.

Many installers also offer east-west layouts, where panels face either side of the roof. These pack more panels into the area, need less spacing, and make more efficient use of the roof, with energy spread across the morning and afternoon. For the general rules, read the best solar panel direction in Canada.

Row spacing matters. If rows sit too close, the front row shades the one behind it in the low winter sun, and a steeper array needs more room than a shallow one. Parapets, stair housings and vents cast shade as well, so a review belongs in the design to optimize the layout; solar panel shading and optimizers explains the options.

How does wind load affect a flat roof solar system?

Wind decides the layout. Air moving over a flat roof can lift panels the way it lifts a wing, and the uplift is strongest at corners and edges. A designer works out the pressure from the building height, the local exposure and the layout, then adds blocks or fixings in the high-pressure zones. Some manufacturers back their tables with tunnel testing.

Several details reduce wind uplift:

  • a low tilt, which keeps the array close to the roof
  • deflectors fitted to the back of the frames
  • setting the array back from the roof edge
  • linking the frames together so the array acts as one mass

In Alberta, chinook gusts and open prairie exposure make this more than a formality, so the design documents should show it.

How much weight can the roof carry, and what about snow?

A flat roof is already designed for snow, and the solar array adds more on top of it. Snow also collects in drifts behind and between rows, which can raise the local loading above what a plain flat roof sees. For that reason, a structural check by a qualified engineer is standard, especially on older buildings or lightweight decks. Local building code sets the design values, and the municipality or the installer can say whether a permit and a structural review apply; see solar panel roof requirements and solar panel permits for the usual questions.

Snow behaves differently on a low array. Panels set low shed snow slowly, so some owners accept winter losses rather than climb a roof to clear them. Walking on a snowy flat roof is unsafe, and snow removal for solar panels covers why waiting is often the sensible choice. Panels still produce in cold weather, and clear cold days can be productive, as described in solar panels in winter.

What should you check about the membrane and roof age?

The membrane is the waterproof layer, commonly a bituminous membrane, EPDM or TPO. Before panels go on, the roofer or inspector should confirm its condition, its remaining life and any warranty terms. Putting panels over a membrane near the end of its life is a costly mistake, because lifting the array later means paying for the work twice. Most owners replace an old membrane first.

Questions you need to ask before installation:

  • Is the membrane compatible with the mounting, and will protective pads sit under the blocks to reduce wear?
  • Does the roof warranty stay valid with solar on it, and who signs off?
  • How will water drain around the array, and is there a walkway for maintenance?
  • Where will the cables run, and how will they cross the roof?

The answers come from the licensed installer, the roofing contractor and the warranty documents, not from a general guide. Costs vary by region, roof type and year, so compare written quotes line by line.

Quick answers

Are flat roofs good for solar panels?

Yes. A flat roof lets the installer choose the slope, so the panels can face south or be arranged in east-west pairs. The extra frames, ballast and wind design add cost compared with a pitched roof.

Do ballasted solar panels damage a flat roof?

A ballasted system avoids drilling through the membrane, which protects it from penetrations. The blocks still press on the roof, so the structure must be checked, and protective pads are normally used under the blocks.

Do solar panels on a flat roof need a permit?

Rules in Canada come from the building code and the municipality, so requirements differ by city. Ask the local building department whether a permit, an electrical inspection or a structural review applies.

What angle should solar panels be on a flat roof?

Flat roof frames commonly use a shallow angle, around 10 to 15 degrees, to limit wind load and row shade. A steeper tilt gains some winter yield but needs more spacing.

Where to verify

Programmes, rules and prices change. Before acting on anything you read here, check it at the source:

  • Natural Resources Canada: federal energy-efficiency and clean-energy pages: programme status, EnerGuide labels, technical background.
  • Your provincial electrical or building safety authority: permit, inspection and code requirements, including the edition of the Canadian Electrical Code in force.
  • Product certification marks: look for a recognised Canadian certification mark (for example CSA) on electrical and gas equipment.
  • Your electricity or gas utility: rates, connection requirements and any utility incentive.
  • A licensed professional in your province: sizing, safety and installation for your particular building; these guides are general background only.

dlsc.ca is an independent information site. It sells and installs nothing and gives no personal advice.

Part of the topic: Solar panels. See all guides on this topic.

More guides on this topic