Drake Landing Solar Community
Home / Solar panels / How much roof space do solar panels need?

How much roof space do solar panels need?

A typical rooftop array on a house needs roughly 5 to 6 m² (about 55 to 65 sq ft) of roof for every kilowatt of capacity. A 7-kilowatt system built from modern panels therefore takes somewhere around 35 to 42 m² of clear roof.

Last updated

How big is one solar panel?

Most residential panels sold in Canada are about 1.7 to 1.8 metres tall and 1.1 metres wide. That works out to roughly 1.9 to 2 m² of roof for each panel, or about 20 sq ft. Panel size depends on the cell count and the rated power, so the datasheet for the model on your quote gives the exact dimensions.

Rated power has crept up over the years. A panel of a decade ago often produced around 250 to 300 watts. Many current panels are rated near 400 watts or higher from the same footprint. Higher efficiency panels pack more kilowatts into each square foot of roof, which matters when the roof is small. The guide on solar panel efficiency in Canada explains what the percentage on a datasheet means and why a few points of efficiency rarely change the economics on a large, open roof.

How do you calculate roof space for a solar system?

The calculation takes three steps, and each one uses a number you can check on your own paperwork.

  1. Choose the system size in kilowatts. If you do not have a figure yet, how many solar panels it takes to power a house shows how annual electricity use turns into a target.
  2. Divide by the panel rating to count panels. Seven kilowatts is 7,000 watts. At 400 watts per panel, that is 17.5, so 18 panels.
  3. Multiply the panel count by the size of one panel, then add an allowance for gaps and setbacks.

Worked example, with stated assumptions: 18 panels at 1.95 m² each is about 35 m², or roughly 380 sq ft. Add spacing for rails and clamps and the footprint grows a little. An allowance of 10% on top gives about 39 m². Divide that by 7 kilowatts and you get about 5.5 m² per kilowatt, which matches the rule of thumb above.

A quick check on any estimate: a 400 watt panel of about 2 m² delivers roughly 200 watts for each m² of panel. That is close to 18 to 20 watts for every sq ft, so one kilowatt takes about 50 to 55 sq ft of panel before setbacks. Online solar calculators run the same arithmetic, and the totals they give are only as good as the roof measurements entered.

How much of my roof is actually usable?

The roof area on a plan and the usable part are different numbers. Usable roof is what remains after you subtract everything that cannot carry panels:

  • Vents, chimneys, skylights and satellite mounts, plus the shade they throw.
  • Setbacks from the ridge, eaves, hips and valleys. Building and fire codes in some places require clear pathways and edge distances, so the rules depend on your municipality and the installer's drawings.
  • Planes that face the wrong way or sit in permanent shade from trees and neighbouring buildings.
  • Weak or aged roofing that needs replacing first.

A common planning figure is that somewhere between half and three quarters of a simple gable roof can take panels. That is a rough guess, and a site survey replaces it. For the structural side, the guide on solar panel roof requirements in Canada covers age, framing and roofing material. Measuring the available roof from a plan, a drone image or a tape on the ground all work for a first estimate, and the installer's drawings determine the final layout.

Which roof direction and tilt work best?

In Canada, south-facing roofs produce the most energy over a year. East and west planes still work and often give a flatter output curve across the day at somewhat lower annual output. North-facing planes are usually a poor choice in the northern hemisphere. The guide to the best solar panel direction in Canada compares these options, including how a steeper pitch helps with winter sun and snow shedding.

Orientation interacts with space. A roof with only east and west planes may need more panels, and therefore more roof, to reach the same annual energy as a south plane. That is one reason an installer may fill both sides of the ridge. Roof suitability also depends on shade from trees, chimneys and neighbouring buildings. Shade on part of an array can cut output for a whole string unless the design uses module-level electronics, covered in solar panel shading and optimizers.

How much electricity will that roof space generate?

Output depends on location, tilt, shade and system losses. As a broad planning range, each installed kilowatt in much of Canada typically generates something like 1,000 to 1,400 kWh per year, with sunnier prairie locations toward the upper end. Treat that as an order of magnitude only. A site-specific production estimate, described in how to read a solar production estimate, is the figure to use.

Using that range, the 7 kW example above would generate roughly 7,000 to 9,800 kWh a year, so the roof of about 39 m² could cover a large share of a home that uses around 8,000 kWh. Whether that is worth the installation cost is a separate question, with cost drivers outlined in solar panel cost drivers in Canada. Prices vary by region and year, and installer quotes decide.

What if the roof is too small?

There are several options to compare, and none is automatically best:

  • Higher-rated panels, which raise capacity on the same area.
  • A smaller system sized to the roof. Many homes are designed this way and the array covers only part of annual use.
  • A ground-mounted array on a property with space, discussed in ground-mount solar panels in Canada.
  • A garage, shed or carport roof. A solar carport can add panel space without touching the house roof.
  • Reducing electricity demand first, since the cheapest kilowatt hour is the one that is not used.

Net metering and interconnection rules can also set an upper limit on capacity, whatever the roof allows. Your utility and your provincial energy ministry publish the current limits. The rules differ by province and change over time, so check them before designing an array to a particular size.

How does this compare with DLSC solar collectors?

Solar heat collectors and solar electric panels are different devices with different space needs. The Drake Landing community in Okotoks, Alberta used 800 flat-plate collectors on the garage roofs of its 52 homes to gather heat for its seasonal storage field, and the layout is described on the DLSC solar collection page. Roof area for heat collection is planned around the heat load, not kilowatts of electricity, so the numbers in this guide do not apply directly. The comparison of solar thermal and solar PV lays out how the two differ.

Quick answers

How many square feet of roof do I need for solar panels?

Plan on roughly 55 to 65 sq ft of usable roof per kilowatt, or about 380 to 450 sq ft for a 7-kilowatt system. The exact figure depends on panel size, rated power and the spacing an installer allows around edges and obstructions.

Can I put solar panels on a small roof?

Yes, but the system will be smaller. Higher-wattage panels fit more capacity into limited space, and some owners add a garage or ground-mounted array. A site assessment shows what the roof can take.

How many panels fit on a 2,000 sq ft house?

Floor area is not roof area. A one-storey 2,000 sq ft house may have a roof of similar or larger size, but only the unshaded planes that face south, east or west count. Roof plans, not floor plans, set the panel count.

Do I need a south-facing roof for solar?

South is best for annual energy in Canada, but east and west planes still produce power. A designer can model output for each plane, and the production estimate shows what each option would yield.

Where to verify

Programmes, rules and prices change. Before acting on anything you read here, check it at the source:

  • Natural Resources Canada: federal energy-efficiency and clean-energy pages: programme status, EnerGuide labels, technical background.
  • Your provincial electrical or building safety authority: permit, inspection and code requirements, including the edition of the Canadian Electrical Code in force.
  • Product certification marks: look for a recognised Canadian certification mark (for example CSA) on electrical and gas equipment.
  • Your electricity or gas utility: rates, connection requirements and any utility incentive.
  • A licensed professional in your province: sizing, safety and installation for your particular building; these guides are general background only.

dlsc.ca is an independent information site. It sells and installs nothing and gives no personal advice.

Part of the topic: Solar panels. See all guides on this topic.

More guides on this topic