Efficient homes, from insulation to net zero
The cheapest heat is the heat a house never loses. Drake Landing homes were built to the R-2000 standard so a modest solar system could do the job, and these guides cover the same ideas for any house.
Last updated
About this topic
The cheapest heat is the heat a house never loses. Drake Landing homes were built to the R-2000 standard so a modest solar system could do the job, and these guides cover the same ideas for any house.
Read about insulation, air tightness, windows, ventilation, passive solar design and what net zero means in practice. They explain concepts and trade-offs, not a plan for your particular building.
All 48 guides on this topic
- Air changes per hour: reading a blower door result: A blower door test pressurizes or depressurizes a house with a calibrated fan and reports leakage, most often as air changes per hour at 50 pascals (ACH50). A lower number means a tighter house, and a tight house must have planned ventilation to stay healthy.
- Cellulose or fibreglass: picking blown-in insulation: Cellulose and fibreglass insulation reach similar R-values per inch, so the decision usually comes down to installation quality, air resistance, moisture and price. Cellulose is dense and recycled, fibreglass is light and non-combustible, and either will perform well when the attic or wall is air sealed first.
- Choosing an insulation R-value for your region: The R-value you need depends on your climate zone, the part of the house and the rules in your province or municipality. Colder regions call for higher values, attics need the most, and the exact required minimums come from the building code or energy program that applies to your address.
- Choosing insulation for your home: Home insulation slows the flow of heat out of the house in winter and into it in summer. The main choices are batts, loose-fill, rigid board, mineral wool and spray foam, and the best one depends on where it goes, how much space there is and how well the area is air sealed.
- Comparing windows by U-factor, SHGC and energy rating: To choose energy efficient windows in Canada, compare the U-factor (lower loses less heat), the solar heat gain coefficient or SHGC (higher admits more winter sun) and the energy rating, ER, which combines gain, loss and leakage into one number where higher is better.
- Designing an energy-efficient home for a cold climate: An energy-efficient home in Canada starts with a compact, well-oriented shape, a continuous layer of insulation, good windows and a very airtight envelope, and only then picks a small heating system to match. Decisions made on the drawing board cost far less than fixes after the walls are built.
- Do low-e windows pay off in a cold climate?: Low-e windows have a microscopically thin metallic coating on one or more glass surfaces that reflects radiant heat, so less warmth escapes in winter and less enters in summer. In most Canadian homes the coating is standard on new double and triple glazing and is worth paying for when windows are being replaced.
- Embodied carbon in a house: what it is and how to cut it: Embodied carbon is the greenhouse gas released to make, transport and install the materials in a home, plus the emissions from replacing and eventually disposing of them. It is counted once, up front, unlike operating emissions from heating and electricity, which accumulate every year.
- ENERGY STAR new homes versus R-2000 and net zero labels: ENERGY STAR certified homes in Canada are new houses built to a performance level above the minimum building code and verified by a licensed energy advisor. R-2000 and net zero ready are separate labels with their own rules, so compare them by their technical requirements, not by name.
- Furnace blower motor problems and what to do: The furnace blower motor spins the fan that pushes heated air through the ducts, so when it fails the furnace can still burn fuel but little warmth reaches the rooms. Weak airflow, humming, squealing and repeated shut-offs are the usual signs, and a technician can tell whether a repair or a new motor makes sense.
- Heat recovery for livestock barns: options and cautions: Livestock barn heat recovery captures heat from the warm exhaust air that ventilation fans push outside and uses it to pre-warm the cold fresh air coming in. In a cold climate that can cut the fuel needed to keep animals comfortable, but dust, moisture and frost make the equipment choice and the cleaning plan critical.
- High performance glazing: when double is not enough: High performance glazing combines extra panes, low-emissivity coatings, insulating gas and better spacers to cut heat loss through a window. In much of Canada triple glazing is the high-performance option, and it makes the most sense in cold regions, in new or deeply upgraded houses, and where comfort near the glass matters.
- How an HRV keeps a tight house fresh without big heat loss: A heat recovery ventilator, or HRV, pushes stale indoor air out and brings fresh air in through a core where the two streams pass without mixing, so most of the heat from the outgoing air warms the incoming air. It is the standard way to ventilate an airtight Canadian house in winter.
- How energy codes shape new Canadian buildings: Canada has no single building code in force everywhere. The National Building Code and the National Energy Code of Canada for Buildings are model documents, and each province or territory adopts them, often with changes, so the energy rules that apply to a project depend on where it is built and when the permit was issued.
- How home energy saving programs are organized: Energy saving programs in Canada are run by federal and provincial governments, electric and gas utilities, efficiency agencies and some municipalities. They offer rebates, evaluations, financing, free or discounted equipment and bill tools, and the mix changes by region and year.
- How to air seal a house, step by step: Air sealing means closing the gaps through which heated air escapes and cold air enters, usually around the attic floor, rim joist, penetrations and openings. It is one of the cheapest efficiency jobs in a Canadian house, and it should come before adding insulation, especially in the attic.
- How to calculate heat loss in a Canadian home: A heat loss calculation adds up how quickly a house loses heat through its walls, windows, roof, floors and air leaks on a very cold design day, giving a figure in watts or BTU per hour. That number is the basis for sizing a furnace, boiler or heat pump.
- How to insulate a crawl space against cold and damp: Crawl space insulation goes either on the foundation walls, which makes the space part of the heated house, or in the floor above it, which leaves the space cold and vented. In cold Canadian climates the wall approach is increasingly common, but moisture control and local code rules decide which one is right.
- How to insulate a garage for cold winters: Insulating a garage starts with its purpose: an attached garage needs a well-sealed, insulated wall and ceiling next to the house, while a detached garage only needs insulation if you plan to heat it or use it as a workshop. Fire separation and air sealing against the house come before comfort upgrades.
- How to know when a skylight needs replacing: Skylight replacement is worth planning when the glass has failed, the frame leaks around the flashing, or the unit is old enough that repairs keep returning. A new skylight is normally installed together with fresh flashing, because most leaks start at the roof seal rather than in the glass.
- How to stop ice dams on your roof: Ice dams form when heat escaping from the house warms the roof, melts the snow above it, and the water refreezes at the cold eaves and backs up under the shingles. The lasting fix is to keep the roof deck cold with air sealing, attic insulation and ventilation, not to chip off the ice.
- Insulating an attic: a step-by-step guide: Attic insulation is usually the highest-value upgrade in a cold-climate house, because warm air rises and the roof is where most of it escapes. The right order is to check what you have, seal air leaks, keep the eave vents open and then add insulation to the depth that suits your region.
- Insulating an older house in the right order: In most Canadian houses the best order is to air seal first, then insulate the attic, the basement rim joist and the basement walls, and treat exterior walls last. This order usually delivers the largest heat savings per dollar and avoids moisture problems.
- Insulating basement walls the right way: Basement insulation works best when moisture is dealt with first, the rim joist is sealed and insulated, and the walls get a material that tolerates damp concrete, such as rigid foam or spray foam, followed by a finished wall. Insulating from the inside is the usual retrofit, while outside insulation is mostly done when the foundation is already excavated.
- Insulating existing walls from the outside: An exterior wall insulation retrofit adds a continuous layer of insulation outside the existing wall, under new cladding. It reduces heat loss and thermal bridging without taking space from the rooms, but it is expensive and disruptive, so it makes the most sense when the siding is being replaced anyway.
- Insulating the walls of an older house: Old house walls can be insulated from the cavity, the inside face or the outside face, and the right choice depends on how the wall is built and how much moisture it handles. Air sealing, attic work and an energy assessment normally come before the walls, because wall work is the most disruptive and often the least efficient dollar spent.
- Is spray foam the right insulation for your house?: Spray foam insulation is a liquid that expands into a solid foam, sealing air leaks while it insulates. Closed-cell foam gives more R-value per inch and adds some moisture resistance, open-cell is softer and cheaper, and both cost more than batts or blown-in fibre, so they are best used where air sealing and space limits matter most.
- Low-e glass: coating types and where they sit: Low-e glass comes in two main families, hard-coat (pyrolytic) and soft-coat (sputtered), and the coating can sit on different glass surfaces inside the sealed unit. Soft coats generally insulate better and are common in cold-climate windows, but the right choice depends on the glazing package and the orientation of each window.
- Net zero home with solar: how big an array do you need?: A net zero home generates as much energy on site over a year as it uses, and in Canada that usually means a very efficient, airtight envelope, a heat pump and a rooftop solar array of roughly 5 to 10 kW. The envelope comes first, because every kilowatt hour not used is a kilowatt hour the panels do not have to make.
- Net zero homes: what the label means and how to build one: A net zero home in Canada produces as much energy on site over a year as it uses, usually with a very efficient shell, a heat pump and rooftop solar panels. A net zero ready home has the efficient shell and the rest of the design but stops short of installing the panels.
- Net-zero energy ready building codes and their steps: Net-zero energy ready code tiers are a stepped scale in the National Building Code that lets a province raise the minimum energy performance of new houses and small buildings in stages. The top tier describes a building so efficient that on-site renewable energy could cover its annual needs, although the building does not have to include that equipment.
- Passive solar design rules for a cold-climate house: Passive solar design heats a house with winter sun through well-placed south-facing glass, stores that heat in the building, and keeps summer sun out with shading, all without pumps or panels. In Canada it works only on top of a very well insulated, airtight envelope.
- Picking a MERV rating for a furnace filter: MERV, minimum efficiency reporting value, is a 1 to 16 scale for how well an HVAC air filter captures particles of different sizes. A higher number catches smaller particles, but it also restricts airflow, so the best filter is the highest rating your furnace and blower can handle without strain.
- Reading an EnerGuide label for a home: An EnerGuide rating for a house reports modelled annual energy use, mainly in gigajoules per year, so a lower number means a more efficient home. One gigajoule is about 278 kilowatt-hours, which lets you convert the figure to something comparable with your bills.
- Removing old attic insulation or adding over it: Old attic insulation usually only needs replacing when it is wet, mouldy, contaminated by pests, fire-damaged or suspected to contain asbestos. If it is dry, clean and simply thin, adding a new layer on top after air sealing is normally cheaper and just as effective.
- Replacing windows to save energy: a practical guide: Energy efficient window replacement means swapping old units for new ones with better glass, frames and sealing, and it pays off most when the old windows are single-pane, leaky or damaged. It is rarely the cheapest way to cut heating bills, so check the attic, air leaks and walls first.
- Sealing door draughts before the cold hits: Door weatherstripping is a compressible or flexible seal fitted around the frame, the bottom and the threshold so that the door closes tight. It is one of the cheapest ways to cut winter draughts, takes an hour or two, and usually needs replacing every few years as the material hardens or flattens.
- Using the sun for free heat: passive solar basics: Passive solar design heats a house with winter sunshine through well-placed south-facing windows, stored in heavy interior materials and kept in by good insulation. In Canada the trick is collecting enough winter sun without overheating the house in summer.
- What a Canadian energy advisor does for homeowners: An energy advisor in Canada is a trained professional who evaluates how a house uses energy, runs tests such as a blower door test, models the results and recommends upgrades. Advisors work through service organizations authorized under the national EnerGuide system, and their reports often unlock program rebates or show that a new home meets a code path.
- What an R-2000 home is and how it is verified: The R-2000 home standard is a voluntary Canadian building specification, introduced by the federal government in the early 1980s, that asks for a tested airtight shell, mechanical ventilation and an energy-performance target. Trained builders construct the home and an independent inspection confirms it.
- What does a net zero house cost to build?: A net zero house typically costs more to build than a code-minimum house, and no single national figure is reliable. The premium comes from a tighter envelope, better windows, a heat pump and a solar array, and it varies with region, size, design and the year you build.
- What happens during a home energy evaluation: A home energy audit in Canada is a visit by a licensed energy advisor who measures air leakage, inspects the house and produces an EnerGuide report with a rating and ranked upgrades. It is the usual first step before insulation, windows or heat pump work.
- What insulation does a house of your age have?: A house's age is a rough guide to its insulation: very old houses often have little or none, mid-century ones usually have a thin attic layer and empty walls, and newer ones have more but still leak air. Renovations and past upgrades change the picture, so confirm what you have by inspecting it.
- What is a net zero energy building in Canada?: A net zero energy building produces at least as much energy on site over a year as it uses. In Canada the usual path is a very efficient envelope, efficient heating and ventilation, and on-site renewable generation, with thermal or electrical storage helping to balance the seasons.
- What is thermal bridging in a house?: Thermal bridging is heat flowing around or through insulation by way of a more conductive material, such as wood studs, steel, concrete or window frames. It lowers the effective R-value of a wall, can leave cold spots that attract condensation, and is reduced with continuous insulation and thermal breaks.
- What makes a home a Passive House?: Passive House is a voluntary building standard for very low energy use: super-insulated walls, triple glazing, an airtight envelope and a heat recovery ventilator keep heating demand a fraction of a typical house. In Canada the standard is promoted and certified through Passive House Canada and the international institute behind it.
- What the ENERGY STAR label means on windows: ENERGY STAR certified windows are products that have been tested and shown to meet Canadian energy performance criteria for the climate zone where they are sold. The label is a quick filter for efficiency, not a guarantee that a window suits your house or that the installation will be good.
- Why windows fog up in winter, and what to do: Condensation on windows in winter happens when warm, humid indoor air meets glass that is colder than the dew point of that air. The usual fixes are lowering indoor humidity, improving ventilation and keeping the glass warmer, while fog between the panes means the sealed unit has failed.
Where to verify
Programmes, rules and prices change. Before acting on anything you read here, check it at the source:
- Natural Resources Canada: federal energy-efficiency and clean-energy pages: programme status, EnerGuide labels, technical background.
- Your provincial electrical or building safety authority: permit, inspection and code requirements, including the edition of the Canadian Electrical Code in force.
- Canada Mortgage and Housing Corporation: housing research and guidance on building envelopes and ventilation.
- A licensed professional in your province: sizing, safety and installation for your particular building; these guides are general background only.
dlsc.ca is an independent information site. It sells and installs nothing and gives no personal advice.