Drake Landing Solar Community
Home / Insulating the walls of an older house

Insulating the walls of an older house

Old house walls can be insulated from the cavity, the inside face or the outside face, and the right choice depends on how the wall is built and how much moisture it handles. Air sealing, attic work and an energy assessment normally come before the walls, because wall work is the most disruptive and often the least efficient dollar spent.

Should you insulate the walls of an old house at all?

Often yes, but not first. In many older Canadian homes the biggest losses are through the attic and the leaky gaps around the structure. Our guide to home insulation upgrade priorities explains why the ceiling and air leaks usually pay back faster than walls.

Walls become the right project when the heating bill stays high after the easier fixes, or you are already opening them for a renovation. An assessment from a registered energy advisor, described in our home energy audit guide, shows how much heat the walls actually lose and what else is cheaper to fix.

What is inside the walls of your old house?

Find out what you have first. A small inspection hole in a closet wall often shows the cavity. Typical older constructions include:

  • Empty stud cavities. Common in houses built before insulation was routine. These are the easiest to fill.
  • Old fill. Sawdust, shavings, shredded paper or loose mineral fill. Some vermiculite products from earlier decades may contain asbestos, so stop and get it tested before disturbing it.
  • Solid masonry or plank walls. No cavity at all, so only the inside or outside face can be insulated.
  • Balloon framing. Open cavities running from the foundation to the roof, which let air and fire travel. These need blocking when they are insulated.

Wiring matters too. Insulation around old knob-and-tube wiring is a safety concern, and the wiring usually has to be assessed or replaced by a licensed electrician first.

Which insulating method works for existing walls?

There are three routes, each with a different mess and cost profile.

  1. Fill the cavity. A contractor drills small holes from outside or inside and blows in dense-packed cellulose, fibre or injected foam, then patches the holes. It keeps the walls intact, but the result depends on a full, even fill, so ask how the installer checks for voids. Our comparison of cellulose and fibreglass insulation and the guide to spray foam insulation cover the materials.
  2. Insulate the inside face. Furring or a new framed wall goes over the old plaster, with insulation and new drywall. It costs floor area and means reworking trim and outlets, so it suits a room-by-room renovation.
  3. Insulate the outside face. Rigid or mineral board goes under new cladding. It handles thermal bridging best and keeps the structure warm, but it only makes sense when the siding is being replaced anyway. See the guide to exterior wall insulation retrofits for that route.

The gain depends on stud depth and material, so ask the contractor to state the expected R-value in writing.

How do you avoid moisture problems in old walls?

This is the main risk. An uninsulated wall leaks enough heat to stay warm and dry itself out. Once it is insulated, the sheathing and old siding run colder and dry more slowly, so a small leak around a window or a missing flashing that was harmless before can start to rot framing.

Fix water entry first: roof edges, eavestroughs, window sills, grade against the foundation. Then deal with air leakage, because warm indoor air carrying moisture into a cold wall causes most winter condensation. The guide to air sealing a house covers the leak points to tackle before any insulation goes in.

Solid brick and stone need extra care. Interior insulation makes the masonry colder and wetter, which can lead to freeze-thaw damage, so these walls are best handled by someone with experience in older masonry. For a house of a given age, our guide to house insulation by age shows what is typically inside.

What does it cost and what rules apply?

Costs vary with wall area, access, method and the repairs the job uncovers, and by region and year, so written quotes decide. Cavity fill is usually the lowest-disruption option, and an exterior retrofit the most expensive per wall when it is bundled with new cladding.

Building codes and some home-energy programs set minimum insulation levels and installer requirements. Check the current rules with your municipality or provincial energy ministry, and the Government of Canada energy-efficiency pages for any funding that applies to wall work in your province. The R-value by region guide helps you set a sensible target for your climate zone.

Quick answers

Can you insulate old walls without removing the plaster?

Usually yes, for wood-framed walls with a cavity. A contractor drills small holes and blows or injects material in, then patches them. Solid masonry walls have no cavity, so they need insulation on the inside or outside face.

Is it worth insulating walls in an old house?

It can be, especially with empty cavities and a high heating bill after the attic and air leaks are done. An energy assessment gives a house-specific savings estimate.

Can insulation cause rot in old walls?

It can raise the risk if water is already getting in or warm indoor air is leaking into the wall. Repairing water leaks and air sealing first keeps the wall drying properly.

Do you need a permit to insulate walls?

Requirements differ by municipality and scope. Blown-in cavity fill often needs none, while a wall rebuild or new cladding may. Ask your local building department before work starts.