Drake Landing Solar Community
Home / Solar panels / Is Solar Panel Fire Safety a Concern for Canadian Homes?

Is Solar Panel Fire Safety a Concern for Canadian Homes?

A properly installed solar system is a low fire risk, and fires that do involve one usually trace back to faulty wiring, poor connectors or damage rather than the panels themselves. The bigger issue is for firefighters, because panels keep producing electricity whenever there is light, which is why rapid shutdown, arc-fault protection and clear labelling are built into modern solar installations.

Last updated

How safe are solar panels from fire?

Solar panels have no fuel and no flame. The fire risk in a rooftop system sits in the electrical parts: DC wiring, connectors, junction boxes, the inverter and the disconnects. Where fires have occurred, causes reported in industry and fire-service literature include loose or mismatched connectors, damaged conductors, poor crimping, water getting into equipment and wiring that was not rated for the current it carried. Panels can also develop hot spots, for example when a cell is cracked or shaded, although a well-designed module is built to limit that.

This is why the work matters more than the product. A neat, code-compliant installation, done by a licensed electrician or qualified installer and passed by an electrical inspector, removes most of the risk. The guides on solar electrical inspections and on permits and inspection show what is checked and why it should not be skipped.

Two points are worth stating plainly. Fires involving solar energy systems are rare compared with the number installed. Yet a fire on a roof with PV systems is harder to fight than one without, because the array can stay energized in daylight even after the main breaker is off.

What is rapid shutdown and how does it work?

Rapid shutdown is a safety function that lets first responders cut the voltage on the roof wiring quickly. A regular string of panels can produce several hundred volts of DC, and turning off the grid supply at the main panel does not de-energize it. Rapid shutdown solves that by reducing the voltage in the wiring close to the array, typically within seconds of a switch being operated or the grid power being lost.

In practice, it is delivered in a few ways:

  • Module-level electronics. Microinverters and power optimizers at each panel shut down output when they lose the grid signal or receive a command, bringing array voltage low. The guide on shading and optimizers explains what these devices do day to day.
  • Rapid shutdown devices. In string systems, devices at the array or on the roof wiring open the circuit when triggered.
  • A labelled initiating switch. A switch or the equivalent is located where responders can find it, often near the service entrance or meter, with a label identifying it.

The Canadian Electrical Code includes rapid shutdown requirements for rooftop solar on buildings, and provinces adopt code editions on their own schedules, so the exact rules depend on where you live and when the system was installed. Older systems may not have it. The local authority having jurisdiction or the provincial electrical safety body is the place to check, and a licensed installer can say whether a particular system meets the version of the code that applied at the time.

What do arc-fault and DC disconnect protection do?

Two other parts matter for fire safety, and both are named in the system's wiring plan.

Arc-fault protection. An arc is an electrical discharge across a gap, for instance at a loose connector or a nicked cable. On DC wiring, arcs can be sustained and hot. Arc-fault detection in the inverter listens for the electrical signature of an arc and shuts the circuit down when it sees one. Modern inverters commonly include it, and the requirement for it is part of the code for rooftop PV on buildings.

DC disconnect. A DC disconnect is a manual switch between the array and the inverter. It lets a qualified person isolate the inverter for service. It does not make the array wiring dead, because the panels remain live on the roof side of the switch whenever light reaches them. That is the reason rapid shutdown exists. The guide on inverters shows where these devices sit.

An AC disconnect, on the other side of the inverter, cuts the connection to the house and grid. A fault that cuts the grid does not necessarily stop the panels from producing on the roof.

What should firefighters know about solar panels?

Firefighter safety starts with treating any solar array as live. Under typical fire-service guidance the main concerns are electric shock, falling from a damaged roof, and the difficulty of venting a roof that is covered with panels and mounting rails. Responders look for solar signs at the meter or main panel, shut down the system if they can, and plan the roof work around what the layout allows. Water is generally the preferred way to fight a fire involving a solar system, used from a distance and following department procedures.

For the homeowner, this makes labelling and information important:

  • Ask the installer to confirm that rapid shutdown labels and the system diagram are in place at the meter or service panel.
  • If a fire starts, call 911, get everyone out, and tell responders the house has solar panels, and a battery if there is one.
  • Do not go onto the roof, touch damaged equipment or spray water at the panels yourself.
  • Keep the roof access paths required by the code clear, and tell the installer before adding structures near the array.

Batteries add another layer, covered separately in the guide on battery safety and installation rules.

How can homeowners lower the risk further?

  • Hire a licensed installer, and keep the permit and inspection records. See the installer checklist for questions to ask.
  • Look at the system twice a year from the ground. Signs of trouble include burn marks, melted plastic, a smell of hot insulation, damaged cable or animals nesting under the panels.
  • Watch the monitoring data. A sudden loss of output on one string, or an inverter fault code, can be an early warning; see what to track in monitoring.
  • Do not attempt DIY fixes to wiring or connectors. Call a licensed professional.
  • Tell the home insurer about the system, and read the insurance guide to see what they usually ask.

Quick answers

Do solar panels cause house fires?

Rarely. Most reported solar-related fires start in wiring, connectors or inverters, not in the glass panels, and proper installation and inspection cut the risk substantially.

Is rapid shutdown required in Canada?

The Canadian Electrical Code has rapid shutdown rules for rooftop systems on buildings, but provinces adopt code editions at different times. Ask the provincial electrical safety authority or a licensed installer about your system.

Can firefighters turn off solar panels?

They can switch off a rapid shutdown device or the module-level electronics, but panels with light on them still produce power in the array wiring, so responders treat the roof as live.

What is the difference between a DC disconnect and rapid shutdown?

A DC disconnect isolates the inverter for service but leaves the array wiring live. Rapid shutdown lowers voltage in the roof wiring itself, so that responders face less risk.

Where to verify

Programmes, rules and prices change. Before acting on anything you read here, check it at the source:

  • Natural Resources Canada: federal energy-efficiency and clean-energy pages: programme status, EnerGuide labels, technical background.
  • Your provincial electrical or building safety authority: permit, inspection and code requirements, including the edition of the Canadian Electrical Code in force.
  • Product certification marks: look for a recognised Canadian certification mark (for example CSA) on electrical and gas equipment.
  • Your electricity or gas utility: rates, connection requirements and any utility incentive.
  • A licensed professional in your province: sizing, safety and installation for your particular building; these guides are general background only.

dlsc.ca is an independent information site. It sells and installs nothing and gives no personal advice.

Part of the topic: Solar panels. See all guides on this topic.

More guides on this topic